Posted on: October 18, 2020


MASTER TL-D Xtreme 36W/840 SLV

Low-pressure mercury discharge lamp with a tubular 26mm envelope


  • Longer lifetime and less early failures lead to less hassle and lower maintenance costs and facilitate the change from spot to group replacement
  • Less waste and disposal cost at end-of-life
  • Special fluorescent coating gives good colour rendering


  • Significant reduction of early failures based upon a new technology (patent pending)
  • Extreme long and reliable lifetime
  • Highly efficient 3-band fluorescent coating in combination with New Generation pre-coating technology
  • Low mercury dose for a long-life lamp (5 mg)
  • Fully recyclable lamp technology
  • End-cap has an x-shaped green bottom plate to distinguish lamp from other fluorescent lamps


  • Suitable for use in applications where maintenance costs (high ceilings, difficult to reach) and disruptive costs are high (stopping of production process, closure of tunnels), or where lamp failure is not acceptable for e.g. safety reasons: tunnels, process, food and petrochemical industries

Warning & Safety

  • To achieve published lifetimes for 100{b9c3e1decd1d9a6381545d5ae59cfbfb6f66ae08352fb0d9f4b009db789225db} operation, do not dim below 30{b9c3e1decd1d9a6381545d5ae59cfbfb6f66ae08352fb0d9f4b009db789225db}
  • When used on electromagnetic gear, it is strongly recommended to apply only Philips S10 or S10E starters (for 18W types S2 or S2E) to achieve the published lifetimes, and to install new starters when relamping.
  • A lamp breaking is extremely unlikely to have any impact on your health. If a lamp breaks, ventilate the room for 30 minutes and remove the parts, preferably with gloves. Put them in a sealed plastic bag and take it to your local waste facilities for recycling. Do not use a vacuum cleaner.

Posted on: August 17, 2020

InfraRed Industrial Heat Incandescent


Instant heat exactly where and when needed

The Philips infrared incandescent reflector lamps are designed to work in the toughest environment such as farm, bathroom or kitchen and their nearest surrounding. They have a reinforced construction thanks to hard glass use. Their compact form and universal cap base allow them to be used with any suitable equipment. A very good method of generating warmth is by using heat lamps. The Philips infrared lamps provide direct, draught-free warmth to the animals, people, but also food. These benefits have made farmers, consumers and cooks around the world choose Philips infrared lamps, because they are the sturdiest, most efficient lamps available for these applications.


  • 30{b9c3e1decd1d9a6381545d5ae59cfbfb6f66ae08352fb0d9f4b009db789225db} extra energy saving with PAR thanks to its unique reflector system
  • Simple and safe heat source with no risk of broken glass
  • 90{b9c3e1decd1d9a6381545d5ae59cfbfb6f66ae08352fb0d9f4b009db789225db} of energy is transmitted as infrared heat.


  • Robust and sturdy hard glass construction of entire range of infrared reflectors.
  • Reflector shape allows concentrated heat to be applied to where it is needed.
  • The design of PAR38 incorporates a completely sealed reflector and therefore high efficiency.
  • More hassle free and handy replacement period thanks to long durability of infrared lamp
  • Red-coloured lamps to reduce visual light emission and glare.


  • Agricultural: breeding and rearing of pigs, poultry, calves, foals, dogs etc. as well as in veterinary clinics, zoos, pet shops.
  • General radiant heating, e.g. hot food displays, cooker hoods, bathrooms, space heating etc.
  • Industrial heating, e.g. drying, baking, carbonising, melting etc.

Posted on: August 16, 2020

Philips Flexo Print

Flexo print TL – high efficiency in reprographics and photopolymerization

Flexo print TL lamps emit almost all of their light (99.9{b9c3e1decd1d9a6381545d5ae59cfbfb6f66ae08352fb0d9f4b009db789225db}) in the useful UVA and visible blue wavebands – between 350 and 400 nm – and have peak intensity at 370 nm (except for the /03 version). This makes them ideal for flexo printing equipment and photo polymerization processes. In addition, the ‘R’ lamps in the family have an internal 200-degree reflector to further optimize the lamp’s overall efficiency.


  • Best match with photo sensitizers
  • Highest output on irradiated area


  • Emit radiation in the range 380-480 nm with a maximum at 370 nm
  • Internal reflector


  • Flexoprint reprograhic equipment, Diazo copying machines

Warning & Safety

  • A lamp breaking is extremely unlikely to have any impact on your health. If a lamp breaks, ventilate the room for 30 minutes and remove the parts, preferably with gloves. Put them in a sealed plastic bag and take it to your local waste facilities for recycling. Do not use a vacuum cleaner.

Posted on: August 15, 2020

TUV Amalgam XPT systems


TUV Amalgam XPT-Maximum efficiency, independent of temperature

Philips TUV Amalgam XPT system consists of an electronic driver that operates one TUV Amalgam XPT lamp, mounted in a sleeve. The electrical specifications are tailored to the lamp, ensuring an optimized performance of the Philips TUV Amalgam XPT system. Thanks to extensive testing before a lamp system is released, we can ensure maximum reliability and long lifetime.


  • Security of effective disinfection over the useful lifetime of the lamp
  • Extreme reliability of driver; with annual failure rate of less than 1{b9c3e1decd1d9a6381545d5ae59cfbfb6f66ae08352fb0d9f4b009db789225db}
  • Approximately 10{b9c3e1decd1d9a6381545d5ae59cfbfb6f66ae08352fb0d9f4b009db789225db} energy savings, because lamps can be dimmed to reach the same UV output compared to similar lamps on the market
  • High system efficacy because it is not required to over-design the purification system to maintain effectiveness of disinfection
  • Best environmental choice because of long reliable life, less waste and industry leading low amount of mercury
  • High efficiency during dimming thanks to unique amalgam temperature control of the 800W lamps


  • Short-wave UV radiation with a peak at 253.7 nm (UVC) for disinfection
  • Special amalgam used for highest efficiency over wide temperature range
  • Protective inside coating ensures constant UV output over the complete lifetime of the lamp
  • Philips electronic driver available for a perfect interface
  • Minimized amount of mercury
  • Universal burning position possible for the T6 range, depending on lamp type and sleeve dimensions
  • Tailor-made solutions possible
  • Lamp can be made from special quartz (open/synthetic) to maximize 185 nm Ozone generation


  • Deactivation of bacteria, viruses and other micro-organisms
  • Municipal drinking water treatment equipment
  • Process water treatment equipment
  • Swimming pool units
  • Equipment for the production of ultra-pure water, for example for the semiconductor, pharmaceuticals and cosmetics industry (ozone version)

Warning & Safety

  • A lamp breaking is extremely unlikely to have any impact on your health. If a lamp breaks, ventilate the room for 30 minutes and remove the parts, preferably with gloves. Put them in a sealed plastic bag and take it to your local waste facilities for recycling. Do not use a vacuum cleaner.
  • DANGER: Risk Group 3 Ultra Violet product. These lamps emit high-power UV radiation that can cause severe injury to skin and eyes. Avoid eye and skin exposure to unshielded product. Use only in an enclosed environment which shields users from the radiation.

Posted on: July 15, 2020

Philips LineBase

Amazingly Linear,Brighter, Comfortable and Safer

BGP472 LED48/72 NW 40/60W

LineBase is breakthrough lighting for city tunnels and underpasses. It’s amazingly linear lighting, yet is easy to install, and it’s the ideal solution to replace fluorescent lighting. The customised lumen output of LineBase enables lighting designers to have freedom on lighting layout. Its continous installalation is to create a seamless, brighter, comfortable visual effect with less flicker. Its plug-and-play electrical connection and remote waterproof drivers save on costs for the owner. The products pass safety and durability tests to prove the long lifespan.


  • Continuous installation for visual comfort
  • Flexible lumen package for more usage situations
  • Remote driver attached to the housing for flexibility
  • Compact end cap makes it amazingly linear, yet it is easy to install


  • Wattage ranges from 10-60 W, lumen output customized
  • Slim and linear housing, compact end cap with positioning-slo
  • Typical 120-130 lm/w system efficacy
  • IP 67 connector for plug-and-play quick installation
  • Loop-in and loop-out wiring for easy installation


  • RGB colour-changing goes via the DMX512 protocol


  • City tunnel
  • Underpass
  • Road lighting
  • Industrial areas

Posted on: May 11, 2020

Philips SON-T

High Pressure Sodium lamp with clear tubular outer bulb


  • SON-T Pro is a cost-efficient and reliable solution in High Pressure Sodium


  • Clear tubular outer bulb
  • High luminous efficacy
  • Robust construction is vibration- and shock-resistant leading to a reliable life
  • Dimming possible with dedicated gear


  • Road and residential lighting
  • Decorative floodlighting
  • Commercial and industrial applications
  • Recreational sports facilities Outdoor and Indoor

Warning & Safety

  • Control gear must include end-of-life protection (IEC60662, IEC 62035)
  • A lamp breaking is extremely unlikely to have any impact on your health. If a lamp breaks, ventilate the room for 30 minutes and remove the parts, preferably with gloves. Put them in a sealed plastic bag and take it to your local waste facilities for recycling. Do not use a vacuum cleaner.

Posted on: May 8, 2020

HID-Basic Semi-Parallel ballasts for SON/CDM/MH lamps

The HID Basic Semi-Parallel ballast is an impregnated (HID standard) electromagnetic copper/iron ballast for use with an external ignitor for HID lamps.


  • Limited volume of ballast coil; also lightweight
  • Simple installation and cabling


  • Orthocyclic winding process
  • Ballasts equipped with screw terminal blocks as standard
  • Earthing-while-mounting facility (HID Standard ballasts)
  • Low watt losses


  • For use with SON and HPI (PLUS) lamps in road, public, area and industry lighting
  • For use with MHN/CDM lamps in shop, lobby and city beautification applications
  • HID-Basic ballasts should be restricted to built-in situations where relative humidity is limited

Posted on: May 6, 2020

TrueForce LED Industrial and Retail (Highbay – HPI/SON/HPL)

Philips TrueForce LED Industrial and Retail lamps give you a quick and easy payback solution to replace HID lamps in High-bay applications.The solution gives you the LED benefits of energy-efficiency and long-lifetime, plus the initial investment is low.With unique lamp design and compatibility, you can directly retrofit HID lamps with TrueForce LED lamps without changing the fixtures or gear. Multiple beam angle options and high colour-rendering index enhance the lighting distribution while creating a comfortable, safe and high-productivity environment.


  • Instant upgrade and easy to install – less time-consuming and safer working at height
  • Great ROI (<2 years) and extended energy savings of 65{b9c3e1decd1d9a6381545d5ae59cfbfb6f66ae08352fb0d9f4b009db789225db} vs existing conventional systems
  • Low initial investment


  • Direct lamp replacement solution without changing fixtures or equipment
  • High energy efficiency with directional light
  • Crispy white light 4,000 K, CRI80 for better visual colour
  • Long lifetime of 50,000 hrs for operation efficiency
  • Product weight < 1.3 kg


  • Industrial – factories, warehouses, distribution centres
  • Retail – hypermarkets, shopping centres
  • Others – transportation hubs, convention centres, sports centres/town halls

Warning & Safety

  • EM version requires an EM ballast to operate. Please refer to the installation guide or consult a Philips Lighting representative.

Posted on: April 19, 2020

Philips Performance Starters

Premium-quality glow switches range for igniting conventional electromagnetic fluorescent lamps


  • Premium quality ensures trouble-free operation
  • Low maintenance costs through extremely low early replacement levels
  • Secure, safe and fast lamp ignition according to IEC 155 international standard
  • The world’s only starters with no radioactive material inside the glow switch while maintaining high quality performance; patented technology avoids hazardous substances in the manufacturing and recycling phases
  • Flame-retardant components for additional safety
  • Redesigned canister top for easy installation; either with a screwdriver or through improved grip


  • 2-pin ignitor in plastic (flame-retardant polycarbonate) canister with radio‑interference suppression capacitor
  • S2 starters for ignition of low-voltage fluorescent TL lamps and series/single application in high voltage for lower wattages (4 – 22W)
  • S10 starters for ignition of high-voltage fluorescent TL lamps for higher wattages (4 – 65W)
  • Premium reliability with less than 100 early failures per million (<100 p.p.m.)
  • Reliable starting behaviour and lifetime
  • Do not contain hazardous radioactive isotopes for activating the glow switch
  • The shape of the canister is designed for a better grip while installing and replacing the starter


  • Starter replacement recommended when replacing fluorescent lamps


  • Used in conventional electromagnetic fluorescent lamp systems
  • S2 starters for LV applications and low-wattage HV applications (4 – 22W), both single and in series
  • S10 starters for HV applications (4 – 65W) in single application
  • S10 starters recommended for 18W HV single application
  • Starter replacement recommended together with fluorescent lamp replacement

Posted on: April 11, 2020

HID-Basic Semi-Parallel Economic ballasts for SON/CDM/MH lamps

Impregnated (HID standard) electromagnetic ballasts, of copper/iron construction, for use in combination with an external ignitor, for HID lamps


  • Limited ballast coil volume and reduced weight, with minimum watt losses
  • Simple installation and cabling


  • Orthocyclic winding process
  • Earthing-while-mounting facility (HID Standard ballasts)
  • Ballasts standard equipped with screw terminal blocks


  • For application with SON, HPI (PLUS) which are used in road lighting, public lighting, industry lighting
  • HID basic ballasts should be restricted to built-in situations where relative humid is limited
  • For application with MHN/CDM lamps which are used on shop lighting, exhibition, lobby, city beautification lighting.

Untuk Memudahkan Pencarian Produk, Silahkan Masukan "Tipe Produk" pada kolom Search dibawah ini :

News Post

Philips XGP500 OBL
Obstruction Light (Lampu Tower / Lampu Obstivision / Lampu Menara).
Philips Tango G3 LED – BVP38x
The energy-saving Philips Tango G3 LED Floodlight is the ideal solution
Philips TrueForce LED
A simple LED solution for direct HID lamp replacement



privacy policy | disclaimer

© 2021 PT. Sentra Cahaya Nusantara ~ All Rights reserved.

Call Now ButtonTelpon Kami Skr!